We have gathered for you all sorts of laughing codes of washing machines so that you can conduct an independent troubleshooting and understand what the problem is.
Indesit, Ariston
F01 - Problems in the operation of the drive motor due to short circuit in the control circuit.
F02 - no signal on the motor operation from the technogenerator to the electronic controller.
F03 - There are problems in the operation of the temperature sensor.
F04 - the machine signals a fault of the water level sensor.
F05 - Problems with water drain.
F06 - Button malfunction signal in a series of cm in the Ariston Dialogic lineup.
F07 - the car warns that the heating element is not immersed in water.
F08 - Failure in the operation of the heating element.
F09 - a failure in the electronic control.
F10 - Error in the water level sensor.
F11 - There were problems in the operation of the drain pump.
F12 - Communication problems between the electronic controller and the indication module.
F13 - drying failure (faulty control T0).
F14 - drying failure (drying does not turn on).
F15 - Drying failure (drying does not turn off).
F17 - Error in the operation of the locking lock (the door is not closed tight).
F18 - a mistake in the microprocessor.
Candy
E01 - Problems in the work of the door locking device.
E02 - Signal about water supply problems: its level does not reach or exceeds the norm.
E03 - There have been problems in the water drain system.
E04 - the car signals the fault of the water in the water system: its level exceeds the norm.
E05 - Problems with a temperature sensor, no water heating.
E07 - a signal of a problem with a drive motor (a technogenerator is defective).
E09 - a crash in the operation of the drive motor (the shaft does not rotate).
Asko.
E01, Motor Fault - errors in the operation of the drive drive.
E02, Water Inlet Fault - Signal about the problems of the water set.
E03, DRAINING FAULT - There have been problems in the water drain system.
E04 - the machine signals that it cannot provide a sufficient amount of water.
E05, E06 - Problems with water heating.
DOOR LOCK FAULT - The washing machine door closed is loosely.
Floaming - increased foaming.
Overfilling, Over Flov - overflow water in the pot of washing machine.
TERMISTOR FAULT - error of the temperature sensor.
PRESSURE SENSOR ERROR - Level water sensor is faulty.
Samsung
E1 - Error set of water.
E2 - problems when draining water from the system (the drain time differs from the manufacturer installed).
E3 - when set of water, the level "Overflow" has been reached.
E4 - the amount of linen loaded into the washing machine exceeds the norm.
E5, E6 - problems with heat heating.
E7 - Error in the water sensor.
E8 - Temperature regime is not respected.
E9 - The washing machine signals the water leakage.
LG
PE - Problems in the operation of the water sensor.
Fe - tank overflow with water.
DE - problems with the door blocker (check if it is closed tight).
IE - problems with water set: a washing machine cannot dial enough liquid.
OE - problems with the drain: you need to check the condition of the hose and filter.
The UE is a drum balancing violation.
TE - temperature regime is not respected.
LE - error in the operation of the blocking mechanism.
CE - The washing machine signals the overload of the drive motor.
E3 - the system cannot determine the download.
AE - a washing machine signals a failure in the autotrunction system.
E1 - water leakage in the pallet.
HE is a heating TEN broom.
SE - the system detected the drive motor switch error.
Kaiser.
E01 - lack of a signal about the closing of the hatch: Washing will be stopped.
E02 - the car signals that the tank filling time exceeded 2 minutes. At the same time, the system continues to washing.
E03 - Drain of water exceeded 1.5 minutes.
E04 - the car signals the problem of water in the water (tank overflow). In this case, the system stops washing and includes a drain pump.
E05 - the problem of water in water. If after 10 minutes the signal does not receive from the sensor "Nominal level", the machine stops washing.
E06 - problem with drain. If after 10 minutes does not receive a signal from the "Empty Tank" sensor, the machine stops washing.
E07 - water leak in the pallet.
E08 - The power supply parameter does not correspond to the norm. Manufacturers recommend a voltage of 190-253 volts.
E11 - a hatch lock failure is detected.
E21 - Error in the operation of the drive mechanism. Washing stops.
E22 - Drive engine rotates in itself, without a start command.
E31 - a malfunction of the temperature sensor (most likely, this was preceded by a short circuit in the chain).
E32 - malfunction of the temperature sensor (circuit breaking).
E42 - a malfunction, the hatch was blocked within 2 minutes after washing.
Electrolux, Zanussi.
E11 - the car discovered a problem with water in bulk.
E13 - water leakage in the pallet of the washing machine.
E21 - the emergence of problems with the drain: the water was not removed from the tank for 10 minutes.
E23 - the machine signals the breakage of the simistor (control element of the drain pump).
E24 - The emergence of problems with the drain: the system has discovered malfunctions in the simistor chain of the drain pump.
E33 - inconsistent operation of water level sensors.
E35 - The problem of water is discovered. The water level in the working tank exceeds the norm.
E36 - Sensor breakdown, which warns about the inclusion of a fan in the absence of the required amount of water.
E37 - a malfunction of the water level I sensor was detected.
E39 - Water overflow level sensor fault.
E41 - the door of the washing machine is not closed.
E42 - The system recorded a malfunction of the hatch locking lock.
E43 is a malfunction of the Simistor of the locking lock.
E44 - the system has discovered a breakdown of a hatch closing sensor.
E45 - a malfunction in the hatch lock control circuit (in the electronic controller).
E51 - breakage of the drive motor, which was preceded by a short circuit in the control element - Simistor.
E52 - There is no contact between the electronic controller and the taogenerator.
E53 - Violation in the operation of the drive motor control circuit.
E54 - Failure of operation of one of the two contact groups of the reversing drive motor relay.
E61 - Temperature regime is broken, water does not reach the temperature set by the program.
The E66 system detected a malfunction of the TEN relay.
E71 - Disruption of the temperature sensor (increased resistance).
The E82 - the system detected problems in the selector (special device for selection of programs and cycles).
E83 - The system detected an error when reading data from the selector.
E84 - Error configuration of the washing machine.
A source