Who said it is difficult to choose fashionable clothes on a figure with magnificent forms and non-standard measurements? Surprisingly easily and simply with this task, the designer Masha2003 brand "Chic Style" is coping. Look at what wonderful models! Bright, stylish, comfortable, fashionable and, which is very important, easy to perform.
Today we will learn to simulate two of them: dress and jacket →
Let's carefully consider the photo of the dresses whose pattern we have to do.
Cutting under the breast, with a 7/8 sleeve and a wide skirt, which is selected at a connection site with a bodice. The bottom of the sleeve is seeded with a rumble with a rubber or braid. The neck is expanded, round, processed by oblique baker. Breeding out of the side seam under the premium. Pockets are processed on the skirt. Pockets in pockets can be performed in the side seam, and you can "in the frame". Because The dress is free - the fastener will not need. Fabric for sewing - flax, although if desired, you can use wool crepe and blended fabrics for the cold season.
To simulate the model, we need the basic pattern base of the semi-wave silhouette. It can be easily generated by your own individual standards. It is very easy and fast, just enter your measurements, on-line program "Basic Circuit Generator" will do everything else for you.
Technological gains to the freedom of plantation are already laid in the construction and have the minimum necessary values. The degree of fallacy of our model will adjust a little later in the process of modeling due to the drive of the side seams. So, that's what we did.
Waist sweeps ignore. We simulate on.
1 step. We hide the side seams, a little removing them to the side for more in the waist area and even higher, under the premium. We extend the future pattern of the dress, in accordance with the sketch or at your request.
2 step. Raise the waist line 5 cm. Translate the breaststuff in the side seam under the armor.
3 step. Expand and deepen the throat line. Cut off the bodice from the skirt on the details of the pattern pattern and pass, then the simulation will be held on the skirt details.
4 step. On the details of the pattern patterns, outline the longitudinal lines for which cut and push the parts to increase the volume of the skirt. On the front part of the panel, the skirts will place the location of the pocket and the pattern of the burlap itself. The entrance to the pocket is located in the side seam and begins 12 cm down from the skirt attachment line to the leaf part, see Fig.
5 step. Sleeve modeling. Expand the sleeve at the bottom up to the width of the sleeve under the army, cutting in the middle along, dilute according to the scheme so that the pattern turns out to be a trapezoidal (sleeve at the bottom of the premium). Correct the line of the Niza slightly curved curve. Bottom sleeves in a dress was sent to a rubber band.
Pattern dress is ready.
Picture of jacket
A jacket without lining, made of dense tissue type of logat, boiled knitwear or any other similar to non-switching cuts. Sleeve is a single, collar type "apas", without a fastener, on the shelf, false pockets with valves.
1 step. To begin with, we will conduct auxiliary straightfall from the highest point of the neck of the transfer and backs through the points lying 2 cm above the end points of the shoulder, the length of the sleeve length + the length of the shoulder. Note the deepening of the Proucy of 4-5 cm with transverse labels. See fig.
2 step. From the points of the rigging shoulder to carry out the inclined lines of the upper slices of the sleeves. See fig. The width of the sleeve is at the bottom of the wrist girth + the gain free (7-10 cm) to arrange the lower sections of the sleeves, passing into the side seams, given the point of deepening the armor, according to the figure.
3 step. Expand and deepen the neck. We carry the line of the side parallel to the middle line of the shelf at a distance of 6 cm.
4 step. Building a collar "Apache".
After the highest point and the middle (lying at the intersection of the middle line of the shelf and the throat line), the point to carry out auxiliary straight, extend it up and put it on it to postpone the length equal to the length of the neck of the back. This segment is issued by the curved line. This is the folding line of the collar in the neck of the back. The floor with a straight angle to it, to the right, postpone the width of the collar 8-9 cm and connect the leaky convex-concave line, see fig., With a point that restricting the collar "Apache". According to the sketch / photo of the model, the end of the collar lies at the level of the depth of the armor, and its width is approximately 20-25 cm. For the most accurate definition, we advise you to make a layout from inexpensive tissue.
The pattern of the original jacket is ready. Good luck to you in the sewing! Be beautiful!
Inspirational examples from designer Masha2003 brand "Schic style"
Source ➝