How to hang the shelf smoothly and quickly even on the wall of plasterboard.
Almost every man knows the situation when you need hang shelf , picture or TV, while it is advisable to make all the work quickly and reliably. We have collected useful tips on how with minimal efforts to cope with this task, even if the screws have to screw into the wall of drywall or if there are no fasteners at hand. To learn how to master the shelves, you need, of course, skill. However, the experience is better to gain when you know exactly what to do. You definitely do not need an excess hole in the wall, our lifehaki will tell me how the first time to achieve the desired result.
1. How exactly hang the shelf with a healent and level
How to hang the shelf smoothly with the isol and level.
The first thing to do is to decide where the shelf will hang. Consider several important points at once: the regiment should be placed too high so that it was convenient to take things from it, and she should not interfere with you in the room.
Once you decide on the question "Where to hang?", Start the part "How to hang?". If you have a brick wall, then for measurements you can use the polenta, which is easy to glit to the wall, and after - to remove. To accurately note the points where you need to screw the screws, we recommend to measure the distance between the loops on the shelf, and then cut off the piece of tape of such same size. Next - to determine the point where the screw for one of the loops will be located, apply the level (now the shelf will accurately hang exactly!) And stick to it isolate.
Measure the length of the tape.
Screw the screw in the right place.
Now there is a drill to drill holes close to the isolate, score dowels and screw the screws. By rejoicing the polenta, you can safely hang the shelf!
The shelf hangs on a brick wall.
2. How to hang the shelf without fasteners
How to hang the shelf without fasteners.
The shelf without corners and brackets can be hung in the corners of an apartment or at home, and such places, agree, most. At first, it is necessary to note the place where the regiment will be located, then check whether the shelf is adjacent to the wall tightly.
Drills holes in the wall.
The next step is to drill four holes under the dowel. So that in the future the regiment could withstand heavy loads, you need to screw internal screws into 2-3 mm lower than the external one.
Internal screws should be 2-3 mm below external.
Next - to sharpen or bother with a pliers of a screw screw or dowel and drive these screws into the holes so that the spikes are outside.
The spikes will serve for the shelf.
Now the shelf must be applied on top of the spikes, and mark them with a pencil. After that, we move the shelf around the outer short angle, and also we note the extreme position of the thickens with a pencil. Received the trajectory of moving the projection of each spike. We combine the middle of the width of the shelves and the projection of the grooves for these spikes, here you need to drill neat holes. At the end, promoting the groove edge of the drill. Now you can fix the shelf on spikes. Such a fastening of the shelf is very reliable and will withstand the load in several kg.
Professing the grooves of holes by the edge of the drill.
Hang shelf.
The shelf with such a mount withstands heavy loads.
3. How to hang the shelf on the wall of plasterboard
Getting Started with a drywall wall, it should be remembered that all gypsum partitions are attached to a metal frame, which means that the place for the shelf is better to choose where the screw can be screwed into the metal. Find a simple simple profile - use a magnet.
The use of a magnet to determine where the metal frame is located.
To work with plasterboard, you need to take special screws that, when screwing, do not destroy the gypsum. Screw to the profile using a screwdriver. Most likely, you will need to make a slight effort.
Screws for plasterboard walls.
Important note: Screws for drywall look a non-zero, but only them should be used. If you need to put a more presentable screw to this place in the future, then unscrew the black and replace it with metal when the hole is already drilled.
Remember that metal profiles are located at a distance of 60 cm from each other, so if possible, pay attention to the shelves of the appropriate size.
Screw screw in a metal frame.
If there is no possibility to drill the wall only in those places where metal profiles are located, then use a butterfly dowel. In this case, drill a hole in the right place, insert and score into the hole of the dowel (after closing the "wings" so that they have placed on the other side of the wall), and already in it - screw the screw.
The butterfly dowel is indispensable for plasterboard walls.
A butterfly dowel is thrown into the wall arbitrarily.
Screw in the wall of plasterboard.