- Beads: blue, green, light green;
- Wire: 0.3 mm, 0.8 mm;
- threads of Moulin of Bolotnaya Color for winding the twigs;
- Pot, sisal, alabaster, PVA glue, scissors, brush, nippers.
The process of manufacturing hydrangea I divided into 4 stages.
Stage 1
Flower Weaving (Blue Beads, Wire 0.3mm)
For our hydrangea it is necessary to make 47 small flowers (you can do more, then your hydrangea will be more lure).
Cut off 60 cm wire 0.3 mm
We ride 7 beads
From one edge, we retreat 10-12 cm
Cut the loop as shown in the photo.
Next, we do not consider the beads, we have a second row of beads around the first looping so that it fits most closely to the loop and twist the wire as in the photo. The third row is made similarly to the second row. The first petal of our flower is ready.
We retreat from the first petal approximately 1 cm and make a loop of 7 beerin. We repeat the process of manufacturing the first petal. For a flower, 4 petal needs.
Next, we ride 3 bispers, we throw the wire as shown in the photo, placing the beerts in the center of the flower. Two-end wire twist, forming a flower stalk.
2 stage
Leaf Weave (Light Green, Green Beads, Wire 0.3mm)
For weaving the leaves, I mixed green beads and a little light green. You can weave purely green.
Cut the wire 130 cm. Form the axis. On the axis we ride 28 bispers, make a loop, so that the beads did not crumble. We ride the working end of the wire approximately 80-81cm of beads, we make a temporary loop.
Next, we do not consider beads, the main thing is that each row firmly lightened to the previous one. It is necessary to make 2 full turns. Next, it is not redeemed to the top, we will retreat from the top 6 of the bisper and between the 6 and 7 bisper we skip the wire. Similarly, repeat the process for the other side.
To complete the arc leaf, we make one round at the base of the leaf leg. Weave, as shown in the photo.
It is necessary to make 15 leaves (you can do more).
3 stages
Winding of twigs, hydrangea assembly (wire 0.8mm, threads Moulin, PVA glue)
To begin with, each leaf and flower are winding with Moulin threads. Watch up the most tight. Watch that the wire is not visible. Catching up to the end, cut off the thread and slightly dripping the plow glue, so that the thread does not work out.
The winding process is shown on the leaflet (see photos). Flowers wind similarly.
Now proceed to the assembly. We need 5 sprigs:
1 Twig of 5 Flowers and 2 Sheets
2 twigs of 9 flower and 3 sheets
1 Twig of 11 Floweries and 3lists
1 Twig of 13 Floweries and 4 sheets
Collect the flowers first. We form a bunch, wind by threads. Catching 5-7 cm, add a wire 0.8mm (approximately 25-30cm), tighten the threads, then add leaves (see photos).
Having cut off a string, do not forget to fix the PVA glue so that nothing worries.
Spins are ready. Now every twig is tight as much as possible to each other, forming a hortensier bush (watch a photo).
4 stages
Planting hydrangea (pot, paper, alabaster, water)
We prepare the pot. On the bottom we put some paper (so that when soaring alabasra, the pot has not cracked).
We divor the alabaster with water to the consistency of sour cream. Pour our hydrangea. We wait until the alabaster freeze (this happens quite quickly )
The smallest left ...
To make the completed view of our work, you can lay sisal on top of alabastra, or to re-establish with beautiful pebbles. In general, here the adviser is your fantasy.
