Flowers are small gentle creatures that bring beauty to our life. And whatever season was not on the calendar, live flowers always warmed and inspire. And the charm of artificial colors, of course, is that they are not faded and can not only decorate the house, but also to "dismiss" on the dress and add hairstyle. Let's delight your favorite girls with a new accessory, make flowers from Foamiran with your own hands on the master class "Cross"!
For work, we will need the following materials:
- Foamiran light pink
- Foamiran Pink
- Foamiran yellow
- Foamiran light green
- Templates of petals
- Scissors
- Glue gun
- Stychkin
- Three beads
- 3 Beads Leaves
- Gold braid 3 mm wide
- Kapron tape Light - green 3 cm width
- Capron Tape Green 2 cm Width
- Scrunchy
- Lighter
- Color hand
- Thicks
- Needle
Cut the petals of colors from Foamiran by templates:
We supply patterns on the Foamiran. For large petals, we take bright pink foamiran, smaller on the light of the Foamiran. Yellow Using for a middle of a flower: Cut a strip of 12 × 1.5 cm. From the Foamioran light green, cut the square with a side of 3.5 cm.
Cut the petals, making the edges slightly wavy. From the green, we cut a chashelistic. Asking strip cut into small stamens across, not reaching the end of about 3 mm.
Twisting petals and a cups along.
We are straightening petals and cups. Each petal around the edge (from a wide hand) heats the lighter and stretch a little. We do not touch the narrow part - it will be glued to the middle.
Yellow stripes Tin the color handle of brownish color on both sides.
We glue a braid (about 14 cm long) to our future middle.
We start twisting the middle, slightly pulling the foamiran at the base. The stamens cut in half and glue to the middle at the base.
Thus we glue all 10 stamens. The middle, winding every circle, lowered below. Inside the middle it turns out higher than on the edge.
As a result, we did:
And now carefully look at how to make flowers from Foamyran. We glue the first row of petals from light pink phoamyran, the planting one after another. The adhesive is needed quite a bit so that it is unbridling not to spoil the naturalness and flower airiness.
The first row is ready.
We draw up a second row of petals using a more rich color.
Next, they pierce the chashelistic toothpick in the middle and proceed through the braid. Fix hot glue at the base of the flower. Flower from Foamiran is ready.
View of the Flower from Chesselistic
At this stage, in principle, you can stop. Flower can already be worn, like a brooch, attaching a metal blank for it (sold in needlework stores). If you want to make gums or hairpins from the Foamiran, then watch the master class on.
Cut from the braid 3 times at 14 cm. We ride a bead and petal on each braid.
Tie a nodule from the braid (tightly near the beads).
Light kapron tape (37 cm long) we collect with a needle, pre-melting the edge of the tape.
Tighten into the ring, fix the stitches and the knot.
We take the second ribbon, the color of the brighter (2 - 2.5 cm wide). And we repeat the same with it as with the first ribbon. We fasten two circles out of the ribbons.
We mount the edges of the braid (there is a stock of approximately 1 cm), we melt the lighter and rush to the base from the tapes (you can first simply outline their position with one stitch. If you immediately seize, it will not be possible to fix the flower in the center).
Take the flower flashes in the middle of the base.
We take a hair gum and fix it with braid. The residue of the braid is displayed back. Hot glue fix the gum.
Now you can consolidate all our "boutons", as well as the flower itself. And the final barcode - hot glue we glue in the center of the flower, hiding all the ends of the braid.
Now you can give at least on March 8, at least for a birthday, or even without reason!)
And one more master class: pretty simple roses from Foamiran on a rubber. It looks very worthy!
If you want to visually see the methods of attaching colors from Foamiran on the rim, hair band and clamp, then watch the master class:
