We continue to make furniture objects from beads. Today we will do a sofa.
We need:
- Beads number 8; I took the three-colors beads: blue, green and yellow;
- 1 meter wire with a diameter of 0.3 mm.
First, from the green bead, using the technique of parallel weaving, make the sofa seat. The seat consists of 6 rows, each of which is 20 beery. Moreover, the first row of beads should be placed not in the middle of the wire, but a little away from her so that one of the ends of the wire turned out to be about 15 cm longer than the other. If you do not want to measure the difference, you can do it easier - initially take a 15 cm wire longer and start weaving on her middle.
Next, we make the back of the sofa. Choose a longer end of the wire, we recruit 36 blue beads on it,
After that we skip this end of the wire through the first 4 beads of the last row of the seat from the opposite side.
Pull this end of the wire until you stop. Blue bispers formed an arc over the sofa seat - the outer border of the back.
Next, we type 7 yellow beery on the same end
And we skip this end of the wire through the beads of the back of the sofa from the 13th to the 16th on the background, counting from the end where the second end of the wire comes from.
Pull this end of the wire until you stop. The segment of yellow beery formed the inner crossbar of the back.
Next, we recruit the wire for another 7 yellow beery
And we skip it through the beads of the last row of the sofa seat from the 9th to the 12th on the background, counting from the same end from which the second end of the wire comes out.
Pull the wire until you stop. We turned out the second rebel of the backrest from yellow beery.
Similarly, we make the same yellow crossbars on the back. At the next step, we recruit 7 yellow beads on the same wire, count on the outer part of the back of the sofa 4 bispers from the last yellow crossbar and we skip the wire through the following 4 beverages (that is, we skip the wire through the beads of the sofa backs from the 21st to the 24th , believing from the end where the second end of the wire comes from).
Next, we recruit more than 7 yellow beads on the same end and we skip the wire through the last 4 bispers of the last row of the seat.
Pull the wire until you stop - the back of the sofa is ready.
Go to the manufacture of armrests and legs. First we make them on one side of the sofa. We recruit on one of the ends of 6 blue beads,
We hold the last dialed beerink and skip this end of the wire in the opposite direction through the nearest beerinka.
Pencing the beads close to the product and tighten the wire tightly.
Then we recruit the wire of the wire 10 more blue beads,
And again, holding the last dialed beerink, we skip this end of the wire in the opposite direction through the beerin's neighboring it.
Move all the beads close to the product and tighten the wire tightly.
Next, we score on the same end of the wire more 4 blue bispers
And, leading this end of the wire from under the bottom of the seat, we skip it between the 1st and 2nd row of the seat.
Pull the wire until it stops so that the last biserinks will be ridiched in the seat,
And make this end of the wire turn around the skeleton of the seat between the 1st and 2nd row.
Then we recruit the wire of the wire 11 blue beads
And we skip this end of the wire through 3 last blue beads of the backrest sofa, adjacent to the seat, and wire leading to the seat.
Armrest and legs on one side of the sofa are ready. It remains to secure the end of the wire from this side: winding it into two or three turns around the back legs of the sofa in the place where the leg is adjacent to the seat, and the excess wire tip is cut off.
Similarly, on the other end of the wire, we make the second armrest and the feet of the sofa.
We grind the seat, back, armrests and legs, giving the product thus the necessary form. The sofa is ready!
A source