Materials and tools for belt beads:
White beads with a diameter of 3 mm - 130-150 g,
Steel color beads with a diameter of 2 mm - 100-120 g,
Mononize white color with a diameter of 0.25 mm long 50-60m,
Steel Buckle,
Needles for weaving - 2 pcs.
Perform work belt belt.
White bead grid.
We start working with white beads. Taking a thread with 2 needles at the ends, perform a mesh in the form of squares. We ride 8 beads on the middle of the thread and spend the left thread through 2 extreme beads on the right thread. Thread stretch. It turned out the first square (Fig. 1).
Then we ride on the right thread 4 beads, on the left - 2 and stretch the left thread through 2 extreme beads on the right thread. The second square is ready (Fig. 2). In the same way, we perform 5 squares. On the fifth square of the threads we cross in two lateral beads (Fig. 3). It turned out the first row.
We carry out the second row: we ride 6 beads on the right thread and carry out the right thread towards the right through 2 extreme beads. Thread stretch. It turned out the first square of the second row (Fig. 4).
Next, we ride 4 beads on the right thread, and we carry out the left side of the previous series through 2 lateral beads on the right thread. It turned out the second square of the second row (Fig. 5). The remaining squares are made in the same way. In the way we can weaken a grid of squares with a length of 70 cm.
Grid made of steel beads.
Next, first on the one hand, then on the other at the ends of the white grid, you reach the mesh from the steel beads. We are wearing it, too, in the form of squares (photo 6). From one end, the grid length is 17.5 cm. The tip is made in the form of a cone (photo 7).
We take the thread from the fifth square in the fourth, crossing the threads in two extreme beads. We ride on the left thread used beads, right-handed in 2 extreme beads (Fig. 8).
Next, we ride 4 beads on the left thread, and the right-handed over 2 lateral beads of the previous series and 2 extreme beads on the left thread (Fig. 9).
Then the right thread is carried out through 2 lateral beads of the previous row and we ride 4 beads on it. Left thread We draw in 2 extreme beads on the right thread. We get 3 squares (Fig. 10). Finish the cone 1 square. We remove 2 threads in 2 extreme beads of the second square.
We ride on the right thread of 6 beads, fix the node of both threads (Fig. 11).
Buckle.
On the other hand, on the end of the white mesh weave the grid of steel beads in the form of squares. Its length is 13 cm. The grid turn around the buckles, fix from the wrong side (photo 12).
We ride 1 bead on the right thread, then we produce it in 2 side beads of the main web. Next to the right thread we ride another bead. Left thread do the same bead. We carry out the threads, respectively, on the right side of 2 extreme beads and on the left side - in 2 extreme beads. Similarly, we make fasteners of the rest, at the end we will tie the node (Fig. 13).
Drawing on the grid.
In the next step, we perform a drawing with steel beads on a white grid. We begin to weave from the middle of the white grid by the method of overlay. In the lower square in 2 horizontal beads, we produce the thread on the right left.
We ride 3 beads, then we produce a needle in 2 parallel square beads of the square (Fig. 14).
Then we ride 1 bead, we draw a thread in the bead in the middle, we ride more than 1 beads and produced the thread of the neglection in 2 square beads (Fig. 15).
Then we derive the thread into the second square of the next strip and thus we make the overlap from steel beads according to the scheme (Fig. 16). When the rhombus is ready, retreat 2 squares on both sides and weavers collections (photo 17, Fig. 18, 19).
From the pattern in the middle, we retreat 5.5 cm in both directions. Further, first on the one hand, then with the other weave the pattern consisting of two bands (photo 20). Breeping the thread on the lower square on two horizontal beads to the right left, we ride 3 beads, producing a thread in 2 parallel square beads of a slightly neglection of the square (see Fig. 14). Then we ride 3 more beads and produce them in 2 beads parallel to the lower beads, mastock from the next square.
Similarly, we perform all 5 squares, moving upwards (Fig. 21).
Next, weave from top to bottom. We ride 1 bead, we felt in the second bead of three steel.
We ride another beads, we draw in 2 white square beads (bottom of the macock) (see Fig. 15). Similarly, we ride all 5 squares to the nose itself (Fig. 22). Next, retreat 1 square to the side and weave in the same way the second strip from steel beads (photo 23).
Then retreat from the pattern with strips another 5.5 cm and weave the pattern consisting of one side of the rhombus and two half-hours and belts on the other side (photo 24).
Bulk.
To secure the tip of the belt, weave the chain of squares. We ride 8 steel beads, taking a thread with 2 needles at the ends, carry out the left thread through 2 extreme beads on the right thread. Pretty stretch. The first square turned out (see Fig. 1). Then we ride on the right thread 4 beads, on the left - 2 and stretch the left thread through 2 extreme beads on the right thread. It turned out the second square (see Fig. 2). Thus, weave 6 squares.
Then we make 1 semi-duct: we ride 3 beads on the right thread, on the left - 1 bead, stretch the left thread through 2 extreme beads on the right thread (Fig. 25).
Weave another 6 squares. We connect the chain by a semi-shield. We ride on the right thread 1 beading, on the left - 1 bead. We do the right thread in 2 extreme beads of the beginning of the chain. It turned out 1 square. Then, on the other hand, we felt the left thread. Correctly fix (Fig. 26). The connection is performed by putting the chain directly on the belt (photo 27).
Belt of bead Ready. This is an excellent accessory for dresses, trousers or blouses.
A source