Today I will tell you about how to create an exquisite spring accessory "Jasmine branch" from selfless polymer clay (cold porcelain)
The master class is quite detailed and comes up even beginners, but I hope that experienced craftswomen will find something useful in it.
For master class you will need:
• Selfless polymer clay smooth (for example, Modena Clay, Modern Clay, Fleur, etc.)
• Manicure scissors with straight and rounded ends.
• Main stack.
• Circumgars.
• Stack with balls.
• Molds of the Hortensia Leaf (or any universal List Mold)
• Optional! Mold with a shallow texture for petal (in this case I use Molda Phalenopsis petal)
• Wire (green) №24.
• Oil paints: herbal green, bleel zinc.
• Two synthetic brushes No. 6 (for decisive paint)
• Tape tape green.
• Ready fine stamens with a yellow boot.
• Latex glue and super glue.
• glue stick (I use toothpick)
• Oasis for drying flowers.
• Basis for brooches or base for hairpins. Optional.
1. Add a small amount of Belil to clay.
2. Mix thoroughly.
3. Be sure to wrap in polyethylene, for the fact that the clay does not dry.
In this master class, I use ready-made vials.
4. Carefully holding the bunch of fingers, cut off at the scene of the connection.
5. Wire in glue by 5-7 mm and glit to the beam of the stamens. Clear your fingers.
6. We give dry glue and close the place of the junction of Teip-dealer.
7. There should be such a result. For our branch, it is necessary to prepare 5 pcs.
8. Roll over the palm of the pea.
9. Peel turn into a drop.
10. Scissors with straight ends, cut a drop from a round side in half, not coming out of 5 mm to the end. And every half cut once again in half.
11. We must have such a workpiece.
12. Carefully smear each petal. We do it in order for us it would be easier for us to roll out the petal stack.
13. Roll all four petals with a stack, the movement of the stack is fan-like. We try to roll the petal evenly.
14. Gently rolling the edges of the petals.
15. Optionally! You can give the texture of petals just in turn, pressing all four petals to texture.
(In this case, I use Molda Phalenopsis Petal)
16. Here is such a flower from us.
17. Putting the flower on the palm, gently give bending to the petals with a stable with a big ball.
18. Apply glue on the base of the stamens.
19. Dress the flower. Make 4 flower. Envy.
20. For a cup of cholestic, take a small green-color pea. Turn it into a drop. We can cut a drop on the sharp side in half and every half again in half.
Roll down every petal stack, trying to leave the sharp tip.
21. Put bending with a stack with a ball.
22. Welcome the base of the flower with glue.
Attention! The flower is better to dry.
23. Wear a cup of petals so that green petals were between white flower petals.
24. We take a piece of clay for green leaf
25. We understand it in the palm of the palm simply by palm.
26. The main stack roll over the layer from the middle to the edges. Up and down.
27. Right and left. We must have a uniform reservoir.
28. Printed on the texture.
29. Cut out the form of a sheet.
30. Gently stacking edges.
31. Cut with screwdrivers with rounded ends.
32. Lower the wire into the glue by 1 cm. We glue to the bottom of the petal.
33. Clear your fingers. I use the shape of the petal.
And leave to dry.
34. In the middle of the sheet, we apply a little green oil paint.
35. Dry brush is cutting.
36. Little flowers for buds make without stamens. Rather petals on ordinary technology.
37. Bud is completely closed. You can add a drop of glue on the petals. In order for it to close.
38. Add a chashelistic.
39. Here is such a bud.
40. Assembly. Attention! Before assembling a sprig, all the flowers and sheets must be completely dried. We begin assembling a sprig with buds. Reinstall Tape tape to the upper bud. Having made a pair of motors connect two more buds.
41. Connect the flower through a centimeter. Then one more.
42. Then two sheets.
43. And two more flower.
44. We take the basis for brooches. We apply to the inner surface. Circle super-glue.
45. Ride the pea of clay, rain and insert it into the hole.
46. We apply glue to the base of the branch.
47. Gently pressed to the base. Leave to dry.
Author of work-man-made flowers from Kalinicheva Elena.
A source