If your husband stopped for some reason to wear a practically new shirt, do not be discouraged - you can sew a completely charming summer or homemade dresser for my daughter!
Products "Dress for a Girl Men's Shirt"
In order to quickly, easily and easily turn a men's shirt in a dress for a girl, you will need:
Men's shirt
Cutting fabric for belt
Cut elastic ribbon (gum)
Sewing machine
2-3 hours of your free time
Immediately note that this dress is sewn very quickly and simple, so even if you have never really kept thread with a needle with a needle - you can safely be done for business.
1. Make the pattern
Immediately, we note that the template below we used for the manufacture of a dress made of men's shirt for a thin girl for 3 years, so try to compare the proportions of the dress with the real proportions of your child's body - there is nothing complicated. Nevertheless, if you do not want to risk, you can use the available dresses or the shirts of your child as a template - then definitely not be mistaken.
Next, we carry the pattern of the template on the fabric using soap or chalk, cut the part, leaving enough cabin centimeters.
In general, the sequence of actions is this:
Immediately, we note that the rear strip of the dress for the girl is cut out of the rear shelf of the men's shirt, and the front - from the front, with buttons.
Getting Started
We fold the details of the dress with the front side inside, fix the pins.
And sew. Leave the allowance of 3/8 or 1/2 centimeter.
Remove the workpiece on the front side.
Sew the second sleeve.
And then the trick both sleeves to the back of the dress.
Then you can handle the seams with overlock or zagazag, but if there is no possibility, you can leave them as it is.
But you need to process the neck, better, of course, overlock.
It should turn out like this:
If there is no overclock - we wrap the fringe edge of the fabric inside twice and thoroughly flying the fold - as they were taught in labor lessons.
In the neck on with you you need to sell a rubber with such a pin, so the overwling neck is bending for the first time, and we have fucked already bent and with the help of such a pin we will then be tired of the gum.
Make sure that the pin passes without any problems, and now.
Fix the neck with pins and flashing on a typewriter, without forgetting to leave a hole for the "input" of gum.
Now the neck actually becomes similar to the neck.
We finish working with the sleeves and sides of the shelves.
If there is no possibility to handle seams with overlock or zigzag, use the old good method of double bending and processing a hot iron.
Do not forget to move the seams.
And do not forget to easing the sleeves.
In them we will insert a gum, so leave in advance the holes for this.
Go to the last strokes, or rather - to the belt.
First we are determined where we will have a belt.
For our dress, we measured and cut off two pieces of cloth 12 cm wide and 22 cm long plus one and a half centimeter.
We turn each strip, fasten the pins.
We flash.
Soak every detail of the belt on the front side of the side using the pin.
It is not simple.
Press the pin.
Pull it from the opposite end.
Purchase.
We apply each detail of the belt over the dress on both sides.
We plan on the belt line dresses.
We shoot and cut up too much.
Apply the belt details to the dress again.
Fix pins.
It looks like this.
We make a line from above, leaving a small hole in which we will be rumming.
By the same scheme, we work with the lower edge of the belt.
We make two lines in the middle.
Do not forget about the holes for the gum.
We got like this:
Now it's time to talk about the rubber band. It is a very important component of our dress, since it is inserted into the neck, sleeves, belt.
Total on both sleeves we have a total of 9.5 cm of gum;
On the belt - 50 cm on both shelves;
and 47 cm on the neck.
Rubber do with a pin through specially left holes.
The ends of the rubber band are sewn.
It turns out like this.
We produce this procedure with a rubber band twice on the belt.
On the neck and sleeves.
Do not forget to cross the gum and sew the hole left for it.
As a result, it turns out like this:
It remains only to handle the hem of dresses.
Turned up everything carefully.
Congratulations! Dress for a girl from men's shirt is ready!
Wear on health!
A source