The collar is your own hands is an excellent and inexpensive alternative to the purchase. We offer you a few step-by-step lessons of its creation from nylon slings, leather and braided with lace.
Nylon tape collar
You will need:
- nylon strip (2.5 cm wide);
- ribbon with a pattern (2,5 cm wide);
- Plastic fastex clasp (2.5 cm);
- plastic dummy buckle (2.5 cm);
- half-trip (2.5 cm);
- Threads.
Tip: For a puppy, a small dog or cat, you can use the above 1.25 cm.
1: Sew color tape to the sling. To do this, adjust the sewing machine to sew the coarse tissue and set the stitch length by 2 mm. So that the seam is located as close as possible to the edge, install the needle on the right side. Purge the tape along the entire length on the right and left, as well as across the edges.
2: fastening the fastener
Disseminate the fastener and thread through it one end of the sling. At the same time, the end of the tape should be about 4-5 cm long. Then bend the end and susht it to the tape, paving the stitches into several rows. Then thread the free end of the ribbon across the half-trip, slide it as close as possible to the fastener and again position the slings again to secure the semir.
3: Take the free end of the slings again and thread it across the plastic dummy buckle, then through the second, not yet crawled, the detail of the clashes. After that, again, press the sling through the buckle, making the second loop under the first one (see picture).
Take the end of the sling, remove it back and place several times across, fixing the two-dollar buckle. To make it easier for you to sew, move the fastener back. Congratulations, you finished!
Lesson number 2: Braided collar
You will need:
- nylon cord;
- plastic carbine;
- lighter;
- scissors;
- a small ring for keys;
- centimeter;
- Painting tape.
Fold the cord in half and thread it through the carbine. Make a loop, stretch through it two free end of the cord and tighten. Take your own collar, and measure its circumference (or measure the length with a centimeter).
Squeeze the length of the cord, equal to the collar circumference, and thread the two free end through the second carbine part, securing it with the painting tape at the desired distance (it's best to glue the carabiner to the table - so it will be easier for you to weave).
Start weave the collar, following the instructions shown in the pictures.
Take the left lace, stretch it under two laces, stretched between two Karabarb items. Take the right lace, stretch it under the left, on top of two shoelaces, and then through the loop formed by the left cord. Tighten the knot. Then stretch the right lace under two stretched shoelaces. Then take the left lace, stretch it under the right, on top of two shoelaces, and then through the loop formed by the right cord. Tighten the nodule again.
After you splured the collar to the end, cut off the extra ends of the lace and burn them away, so as not to bloom. Do not forget to turn the keyword for the keys to which you will later be attached to a leash, a tag with the name of the dog and with your phone number.
Master class # 3: leather collar
You will need:
- skin segment;
- Leather handling knives;
- buckle and semiring;
- awl;
- Decorative rivets.
We recommend using Latigo's skin for collar - it is very durable and does not deteriorate under the influence of dirt and water, while maintaining not only your qualities, but also appearance.
1: With a special knife, cut a piece of skin with the desired width. To determine the desired length, measure your dog's neck coverage and add another 25 cm. If necessary, you can always cut off an extra piece. At both ends of the leather strap, cut the corners to give a complete view.
2: Knife for mowing the corners along the entire length of the collar cut corners. Repeat on both sides. Thanks to this, the leather collar will not rub. With a suitable leather glue on a water basis, process edges.
Tip: Lubricate the collar with a special skin cream, carefully revealed his hands. Then apply a layer of beeswax and remove the remnants with a soft towel.
3: Using a template, with sewing, mark the place where the holes will be located for fastening metal jewelry. Knife for mowing remove part of the skin from the wrong side. Thanks to this, the collar will become easier and softer.
4: Using a selection of different diameters, do the holes in the marked places - for decorations and for fastening the tongue of the buckle. At the same time, do not forget to put another piece of skin so as not to spoil the surface of the table. Scalpel Make a hole for fastening buckles.
5: Credit the end of the collar through the buckle, bend and secure. Then get the semoligo, secure the free end of the leather strap. Decorate the collar decorative rivets.
Our product is ready:
A source