To make a soft aspic with your own hands, you will need:
4 wooden drawers;
2 brus 5x10cm (every about 2.5 m);
4 50 mm roller (with screws);
8 metal corners (with screws);
12 Screws on a wood 30mm long;
4 scouring on a tree 65mm long;
4 screws on a 25mm tree long;
screwdriver;
drill.
In addition, paint will be required, brush and materials for the manufacture of soft tops:
- Substrate from non-restant plywood;
- Tight foam 5 cm thick;
- batting;
- upholstery fabric;
- 5 buttons in tone tissue;
- furniture stapler;
- polyester cord;
- scissors;
- roulette;
- Needles with threads.
Make a pencils with a drawer with your own hands: Step-by-step instructions
Frame manufacture:
1. First, the drawers must first be born. One box is put upside down, and the second is on him, on the end. Ensure that the edges of the drawers exactly coincide.
2. Drill 3 guide holes, as shown in the photo (they will not allow the tree to be born when screwing the screws).
3. Create drawers with 3 30 mm screws.
4. Turn the resulting design so that the ends of the box be on the floor upside down. Install the third box on it and screw it with screws. Repeat the process by attaching to the first three boxes fourth.
Turn the construction for the last time by connecting the fourth and first drawers with screws.
5. From bars, make a frame.
6. Bruks are bonded with a metal corner.
7. For strength, you can add bar in the middle of the frame, also fixing it with its corners.
8. Put the finished frames on the bolds fastened together, as shown in the photo number 5. Make sure it lies perfectly smoothly. Drill along the guide hole in each corner and screw the 65-mm screws by connecting the frame with drawers. Now fasten the roller frame.
Making soft top:
1. Cut Phaneur and Porolan in size.
2. Find the center of the future pillow, drawing a diagonal. Measure it from it 12cm in each direction and put crosses in these places.
3. With the help of scissors, do small holes in the center and on the site of each cross.
4. Place two layers of batting on top, so that he hangs freely from all sides. Gently turn the folded Fanur, foam and batting together, having raised not to move them.
Attach batting around the perimeter to the plywood with a stapler. Make sure it is tightly and evenly stretched. After that, repeat the process described in paragraph number 2, but on the plywood. Drill in the observed openings.
5. Turn over the workpiece back, the Vatin up. Find the holes done earlier and the battles are most as possible in them. With the help of a long needle inserted into the hole below, in the plywood, make sure that the holes in the foam and plywood coincide, aligning them if necessary.
6. Take a button and grind the cord in her ear. Then the thread is both ends of the cord in the needle. Put up the upholstery fabric over the batting, completely covering it and leaving enough fabric from all sides to subsequent attach it to the plywood brackets. Clean the cord through the hole in Vatina, Porolane and Plywood.
7. Press the button down as closely, to the plywood, while pulling the cord. Then quickly lock the cord with brackets. Repeat the process with all buttons.
8. After that, turn over the workpiece and the brackets attach the fabric to the plywood, evenly and tightly pulling it.
Latest touches:
1. Prepare the workplace under painting, covering the floor or table with an unnecessary tissue (polyethylene or oilcloth).
2. Color boxes in the selected color.
3. Cut the excess fabric and cord. Gently put boxes on the pillow, thoroughly alleged the edge.
4. Connect the frame and top by twisting 25mm screw in each angle.
Turn the design. Your soft aspiration in the hallway or living room is ready!
A source