Today I want to turn to the time that arises in the life of almost every person. Bought trousers, but they are not suitable in length. Pants dangle on the floor, or harmoniously harmony around the foot. Of course, they must be shortened. There are quite a lot of ways, but they all depend on the trouser model. How to enhance the pants manually ? This primarily concerns classic models, on which the track from the stitch should not be visible.
For example, I took men's pants. I will note one nuance. In order for the work is not performed in vain, it is first necessary to measure the length of the trousers on a particular person who will be worn in the future.
If you do not have such an opportunity, you can take other pants of this person and measure the length of the pants along the step-down seam, which is located on the inside of the trousers. This time I did. Soap I planned the desired length and started work.
For convenience, I translated the label on the outside side of the pantna and laid the pants at exactly on the table.
The next step, I measured straight angles using a corner that coincide with the position of the label and the direction of the arrows on the back and front half of the trousers. Spent straight lines.
Then the resulting line needs to be slightly fusing in its middle part.
From the resulting line, I postponed 3.5 cm. This is the minimum value that you need to postpone.
There are several reasons for this:
- Pants can unexpectedly sit down and have to bend them. We need a stock.
- Little bending gives a visible seal.
In order for both pants to be cut off the same, they must be folded exactly along the entire length of the trousers, and sometimes it does not interfere and pierce with needles from top to bottom. Be sure to connect with needles both pants on the outlined poda line.
Now you can boldly cut off. If it is difficult to cut four layers of the tissue at once, then do it gradually. First, cut off the excess length on one pant, and then to another.
The position of the needles I transferred soap to the other side.
The same thing I did separately with each panta. Although it is possible to do this and with a centimeter tape, measuring the inner part of the trouser 3.5 cm from Niza. For high-quality bending, it is desirable to handle the resulting lower cut overlock, and the tails of the threads are consistent with the hook inside the lines.
After that, you can proceed to the manual binder. Afterverting the pants on the wrong side, I jolly with needles width of the poda. Be sure to combine lateral seams on the podium and on the pant. Similarly, I paved the needles at a distance of 1 cm from the upper edge of the pent. It is necessary to do so that the pantna does not shift.
Next, I sewed the edge of the poda to the Schword's post. To do this, enter the needle exactly in the line from Overlock (you can even get into the stitches themselves) and capture one or two strands of the pants. Then the needle output again on the line of overlock. The distance between the punctures should not be more than 0.5 -1cm. Thus, we chat pants along the entire length.
That's what I did. It remains to smooth them. If you are dealing with pants, but which are the arrows, then at the beginning, it is necessary to restore the places where they are.
Afterverting the trousers on the front side, I switched the allowance inside the pants. From face to do it undesirable, as Overlock can be printed. Arrows exparate from the front side through a rag.
That's all. On this, the whole process ends.
Now you know how to correctly apply trousers manually, and I am sure that if necessary, you can easily cope with this operation.
Of course, for greater confidence that in the future everything will be fine, it is advisable to draw a new thing. Subject to it or good steam processing, or wet and give dry. This will allow the product to give the desired shrinkage, and you will save you from unrest in the future. Everyone knows that natural fabrics are usually sitting.
But you can risk and climb trousers without preprocessing. This is already at your discretion.
A source