Dear visitors of the site "Visiting Samodelkina" in the article presented to your attention, it will be a question of how you probably guessed the name of the technology of creating a convenient to use the greenhouse, the people of the named casket. This name characterizes its own design itself, because it has a discovering arched half made from metal-plastic pipes and a reinforced polyethylene film. The cover is fastened due to the loops twisted with the old furniture :) due to them and the greenhouse cover is discovered and close, which is very convenient during operation.
We look at the Greenhouse Review
And so consider what I needed to create a greenhouse.
Materials
1) board 30 cm
2) Metal-plastic pipe 16 mm 8 meters
3) reinforced polyethylene film
4) timing segment 40 mm
5) Sheet metal 0.7 mm
6) DPE
7) Nails
8) Screws
Instruments
1) Shopata
2) Topor
3) hammer
4) Hoven
5) Screwdriver
6) Nail-holder
7) Roulette
8) Pencil
9) Scissors
And so to begin with a slight deepening about the bayonet shovel, this is quite enough. The recess in the surface of the Earth will provide a more optimal temperature for seedlings growing in it.
Then neatly solve everything. And proceed to the ruin grooves under the columns from the bar.
Insert the bars into the obtained deepening, and I instinct the earth at the same time thoroughly tamping.
Further, the size saws 2 of the bar, which will be a greenhouse frame.
And so inserted all 4 columns from a bar with a cross section of 40 mm.
Next, I resell on top of the pavement columns in the end parts of the greenhouse.
Then the horizontal also squeezed a couple of bars.
And on the basis of the received isow, moved to the structure of the box.
Inside, it is possible to lay all sorts of branches, leaves dry, sawdust, it is necessary in order to the process of overloading the stuffed material gave useful elements and of course heat.
Then I continue to finish the box.
In the resulting bunker fall asleep the land formed in the process of deepening deepening for the greenhouse.
Fill somewhere more than half, because then the earth will give shrinkage and decrease in volume.
At the edges of the greenhouse, I made a sinking sand.
I make the frame of the opening door.
In the corners, fasten the rails, screwing on the screws.
The resulting frame is fixed with loops from the old Soviet furniture, by the way if you have old furniture and you gathered to throw it away, first think about it and you need it :) Better bring to the cottage and make something out of it, because the boards are suitable for any self-catering in the country.
I screw over the entire length of the resulting frame.
I spend tests :) everything works fine :)
Then I install an arc from the metal plastic pipe, simply screwed the screws at the bottom and that's it.
And so thus secured 3 arcs at the same distance.
Also try to open and close with fixed arcs.
On the resulting design pulling the reinforced, polyethylene film.
That's what it turns out.
I try to open a ready-made greenhouse.
Everything is wonderful, but there is not enough automatic holders of the greenhouse cover :) Each time it is not so convenient every time. Such aka came, place the rails of the desired length along the edges of the cover screwing onto the screw at the top. When opening, they will automatically, will be shifted and fixed under the weight of the door.
That's what happened in me :)
He worked on the greenhouse all day for the span, until it began to be frozen.
After some time, the cucumbers seed out, they were very comfortable in the greenhouse and they went to growth well.
We are very pleased, simply and easily serve, there is no cottage. The only negative is that the box is made of wood and will not last for a long time, but if you have a slate, or sheet metal, it is natural to do from such a material that is not amenable to rotting.
On this end my tale, I hope you enjoyed it :) Thank you for your attention! Come visit the bowl, do not miss newcomers in the world of homemade!
A source