While the wife with the mother-in-law chose a suitable place, I went to Sobetau for the Council and discussed possible options for assembling the soul. Piece of unsuitable for the assembly of the aluminum shelving (hereinafter referred to as the soul frame), the VG cable for electrical wiring, automatic on 25a, 5m reinforced hose, roofing screws, a pair of clamps, two steel plumbing fittings (in general, not badly squeezed) and the process The soul assembly began.
Unfortunately, I did not fall out the beginning of the process. Photographed on the shovel, so the quality is not very. In the meantime, I dug a pit, naturally do two things with one tool could not
I dug a hole about 1m depth and put into it an ordinary steel barrel for 200l. The barrel was already in holes - these are the consequences of burning wood-herbal unsuitable weather conditions
2. Heat the timber with a length of 120 cm, gathered the foundation of the future soul, leaving the gaps between the bars for ventilation. The foundation from the bar installed an aluminum frame from a former rack and brought all galvanized corners. Karkas turned out to be 120x120x220cm
Next, chopped four bands from the work remaining from the construction of the sickness. Bent them in length and laid on the foundation as catchment trays.
Still waterballs
A couple of years ago a cellular polycarbonate was bought and remained unused. Four triangles for collecting water were cut from it and installed on top of the catchment trays.
Fully assembled waterball
From above put the board 45 * 250mm, pre-processing the plane and a twigration along the length
Impertly holes in the board, because The board laid tightly with a gap of only about 1-2mm
Then "wrapped" the whole design into a cellular polycarbonate and put vertical rails from the faceplate from the front side (for fastening polycarbonate) and the rear (for fastening the water heater). The roof made an arched slide, supported by the central board and four corners with a radius under the roof, leaving the "windows" sides for ventilation.
Here you can see how the roof is made
Then I installed the water heater, secured the old plastic shelf borrowed from the bath, and the holder for the watering can.
Waterfloor secured on a rotating bar.
On the ends of polycarbonate put on a plastic end profile
Multied no holes - more diameter (do not watch perfectionists)
Cut off and drove galvanized corner at the entrance to the shower (no one hurt)
Bought for 100 rubles LED lamp and installed next to the watering area (the drinker is in the shower)
The test borrowed 60cm copper tube 5mm, for the curtains on the entrance. The house took the copper pipe ½ (21mm) with a length of 1M, which remained after repairing the bathroom. Passed the soul on the walls and hung the curtain bought for 250 rubles. So it was fenced with a hook zone and towels, as well as the entrance to the shower
The curtain fastened the hanger bought for 200r
Connected electrical wiring while hiding connections to the distribution unit
Shower is ready
4 days of vacation and 550r (hanger, curtain, lantern) were spent on all works.
Passed material and equipment (stocks available):
7M Cellular Polycarbonate
4m plastic end profile
2 three-meter bar 18x18
Collected aluminum frame size 120x120x210
4 corner of galvanized
Small piece of proflist
3 three-meter boards 45 * 250mm
2 two-meter boards 30 * 150mm
Box of roofing screws and pieces of 50 screws on a tree of different lengths.
Garden reinforced hose 5m
2 steel homuts
Crane, connecting barrel with ¾ on ½, tee ½ and two fittings.
JV 3x2.5 30m cable
Blue isolent
Automatic 25A
Terminals 3pcs
Distribution
Presented water heater 15l, 2.5 kW
That's all I wanted to say. Thank you! Criticism is welcome.
a source