As it turned out, I can't do a full-fledged master class for several reasons. The first is fond of and forget to make the necessary photo in a timely manner! The second - there is no means to take pictures, since the lodge house, and my workplace is microscopic and is located opposite the window. It is convenient to create, but to make photos against the light almost impossible ... And run every time to another room on the windowsill troublesome. The third is part of the work at night, when my scoop camera is generally unrealistic to remove something with electrical lighting. Therefore, as I could (when I remembered :)), I documented the process. If something is incomprehensible, I will answer additionally!
So, we will need what is practically in every home and even prepares for emissions! It:
- corrugated cardboard;
- Trimming wallpapers;
- toilet paper;
- trimming leather;
- toothpick;
- PVA glue;
- thermopystole (optional);
- Any paints;
- self-healing mass for modeling;
- a trifle for the decor (buttons, pebbles, shells, beads, smooth or bought flowers);
- stationery knife or scalpel;
- Tassels.
We will do a house as a decorative thing for the interior, but quite a functional, which the child can play, settles its toy characters and furnish with furniture. Therefore, the rear walls will be open.
Let's proceed. First I take corrugated cardboard. Normal, from packaging boxes.
I take the longest cardboard, which was once one of the lids of the eggs for eggs. And I make a stupid side of the scissors of the bend.
Then we have the windows on each future wall of the house.
I cut their scalpel.
Some of the winds I plan to do with jumpers. To do this, I take a toothpick, every end lubricate the PVA thick glue and insert it in this way.
Noticed that the cartons with the windows lies on a piece of wallpaper? Not in vain. With the past house, I suffered when ready-made rooms from the inside had saved. Therefore, this time I decided immediately the inner walls of sacking with wallpaper.
Then I took a thermal storage, the lower cut on the perimeter and glued to the base. The previous house I attached, smearing it with PVA, and fastened additionally with scotch. That is, there are several mounting options. Choose the optimal for you.
It looks terrible :) From another angle is not better!
And this is what the back wall looks like, which will be open to free access.
Then the "frame" cut out from the leatherette. You can use both paper, and cardboard, fabric, and plastic.
Insert the frame from the inside.
Now I cut the rectangle that will be a ceiling of the finished room. I wake it too with wallpaper and gluing.
By the same principle, I do the second floor.
In the attic planning a balcony, so I do a ceiling for the second floor, taking into account the cornice for the balcony.
I stick the second floor ceiling.
Now proceed to the roof. I cut such two triangles with cutouts. One with the opening of the balcony. The second with a large opening to access the inside of the attic.
I stick the roof. I take a smooth strip of cardboard, in length equal to the perimeter of the protruding cornice from the balcony, bend it and stick it.
I also organized a semicircular attack. But it was already in the night deep, so the process did not block the process. But the principle, I think it should be understood.
From another angle.
And here is the attack in all its glory))
Then the whole house is saving toilet paper. Glue diluted PVA.
The roof can not be covered in a whole, as it will be a tile.
The pasting will not only give the toughness and strength of the whole structure, but also create a special test of the dued plaster :)
Rodyshko saves too. It is impossible to do all this at once. You have to wait until the top will dry up to leave the bottom.
After a complete drying of the whole house, soaked it, painting acrylic paint blue. That's just such a palette in stock turned out to be :)
The base-stand is painted in green - there will be a grass.
While the house dries, cut the tile from corrugated cardboard.
And stick it in layers.
Stick on an undiluted PVA.
Roofing after drying paint brown paint. While it dries, out of the masses for modeling, self-sitting in the air, I make bricks, detection, etc.
If there are no masses for the modeling, it is quite possible to do without it! The previous house I decorated with flavors from toilet paper and sliced on bricks corrugated cardboard.
Leave again to complete drying overnight. And in the morning I make the final painting and tint. This is a matter of taste. I decided to make a shapped old house again. Therefore, there was a semi-dry brush with beige paint, then with green, and finally with white.
Closer.
The grass also enliven different Otnekami green.
Now it starts decoration. I use everything that gets at hand!
Here is a flower garden.
The flower garden is practically throughout the perimeter.
House ready! You can change the size, floors, layout, coloring and decor - it will turn out to be the same principle of manufacturing completely different houses.
And here my granddaughter took its homes to operation!
Successful creativity! I hope such houses will delight your kids no less than my granddaughter!
A source