The hit of the season! Simple Press Culota Pattern
One of the innovations of modern fashion, which today is at the peak of popularity - these are wide short-circuited pants-Culota. The name has come to be fashioned not so long ago, however, these trousers that were popular in the 70s have gained the second reading. Thanks to the creative ideas of designers on the podiums, a culwood of a wide variety of styles is represented, with an overwhelmed waist, with a smell, with sweeps, pleated, below the knee, to the middle of the ankle.
The correct length of the trousers can vary in the range below the knee - above the ankle. Such a model of trousers is very convenient in the sock and women who prefer pants to skirts it has already been appreciated. The model that we offer you to sew, ideally emphasizes the figure, and the delicate floral print is a real hit of the season.
Build pattern is very simple, you can do it literally in 15 minutes.
What measurements should be removed?
In order to build the pattern of trousers, it is necessary to take out only 5 standards, you can also use standard measurements from the table of measure for women's clothing. We use size 46 measurements:- Waist girth 72 cm
- Cookies hips 98 cm
- High height 20 cm
- Seat height 26 cm
- Pants length 70 cm
Cutulota Pressure Pattern - Building
Building Front Half Trousers
We start building a trouser from the front halves.
Return from the left corner of paper 10 cm down and 5 cm to the right. Put the point A. from the point and post down to the right AA1 = 1/4 of the girth of the thighs by measurement + 1 cm = 98/4 + 1 = 25.5 cm and down an = 70 cm. Design the AA1NN1 rectangle.
From the point and set aside down Av = 20 cm - the height of the thighs by measurement, ac = 27 cm (seating height by measurement + 1 cm). Spend from the points in and from the horizontal lines to the right - the points B1 and C1 are obtained.
Bath line. From the point C1, set aside to the right 1/10 of the bumping hips + 0.5 cm = 49/10 + 0.5 = 5.4 cm - the C2 point was obtained. From point B1, set aside to the right 0.5 cm for all sizes and swipe the bow from the point A1 through the point 0.5 to the C2 point as shown in the drawing.
From point C2, lower the perpendicular to the bottom of the pants - C2N2.
From point A1, set aside to the left ¼ of the waist girth by measurement + 3 cm = 72/4 + 3 = 21 cm (1 cm for landing and 2 cm on the sweep) - a point A2 was obtained. From point A2 up, set aside 1 cm and swipe the sides of the pants A3B smooth arc.
Tale latch. To find the location of the melting molding, divide the CC2 segment in half and through the division point, swipe the vertical line of the arrow.
To the left and right from the arrow line along the waist line, set aside 1 cm, draw a talet with a length of about 10 cm.
Building the rear halves of trousers Culota
Building rear halves of trousers is made on the basis of front halves of trousers.
Divide the segment A1A4 in half and from the fission point up perpendicular to the segment 2 cm long - point T.
From point C1, set aside 1.5 cm to the left for all sizes - the C3 point is obtained. Connect the points T and C3 by direct segment.
From point C3, set aside to the right segment C3c4 = 1/10 of the thighs by measurement + 1 = 98/10 + 1 = 10.8 cm. Spend a line of the rear seam of trousers through the points T-B2-C2-C4.
From point C4, lower the perpendicular to the bottom of the pants - C4N4.
From point B2, set aside to the left B2B3 = ¼ of girth of the thighs by measurement + 1 cm for landing = 98/4 + 1 = 25.5 cm.
The waist line of the back of the trousers. From the point and place up 1 cm and swipe a short auxiliary line. Spend the line of the waist of the back half of the trouser Tt1 = ¼ of the waist girth + 4 cm = 72/4 + 4 = 22 cm (1 cm for landing and 3 cm on the sweep).
Tale latching rear halves of trousers. To find the location of the molding molding, divide the segment TT1 in half and through the division point perpendicular to the waist line segment 14 cm (the length of the rear melt pulling). Build an exhaustion of 3 cm depth and 14 cm long.
Pants pants. On the front of the trousers, draw a pocket in the side seam, on the back - a slit pocket with a leaflet (Fig. 1).
Additionally, it is necessary to construct a belt length Av = waist girth by measurement + 5 cm (1 cm for landing and 4 cm on an approach to the fastener) and 6 cm wide (in the finished form 3 cm).
For this pattern you can simulate any other style of trousers-cousotov.
a source