![Trsster tare da fitilar](/userfiles/37/4919_1.webp)
Kuna iya karanta jaridar ko littafi a kan kujera na fi so wasu lokuta suna wahala saboda rashin haske. Sayi fitilar baini, amma ya sa fitila da hannayenku ya fi dacewa da hannayenki - ana iya canjawa wuri daga wuri zuwa wuri don dacewa da karatu. Bugu da kari, wannan samfurin zai dace da ciki. A matsayin abu don masana'anta, ana amfani da katako - a ƙasa na Jagora a ƙasa, wanda ake amfani da ash don kera Luminiire.
Ka warware tambayar, yadda ake yin bene a kanka da kuma a gida, bai isa kawai ka san wadancan girma wanda bayanin zai kasance peaked. A cikin littafin da ke ƙasa, ana bayar da duk bayanan da aka bayar - jere daga alamun amfani da ƙare tare da Maɓallin Samfurin.
Muna yin bangaren gado
Mun yanke wadannan abubuwa na kwanon waje na gaba:
bangarorin biyu (a) racks;
bangare bangare (c) racks;
baya (b) rakumi;
bar e, wanda zai kasance a saman;
Bangarorin bangarorin da ke gefe D.
Cikakkun bayanai a, B, C da kuma bukatar yin tare da 25 mm a tsayi, ana nuna su daki-daki zane-zane a ƙasa. Dalilin ƙwarai za a iya bayyana ta rubutu.
![Zane gefen hagu](/userfiles/37/4919_2.webp)
Zane gefen hagu
![Zane daga gefen gefen titi](/userfiles/37/4919_3.webp)
Zane daga gefen gefen titi
Da fatan za a lura! Idan gurbi na gefen gefen rack kuma ya sauke da sauri sanya ramuka na gaba, da wuraren shiga nan gaba kuma "ya fadi "Don yanke duk nau'ikan iri ɗaya ko symmetric.
![Cikakken bayanin bishiya tare da fitilar](/userfiles/37/4919_4.webp)
Cikakken bayanin bishiya tare da fitilar
A kowane ɗayan bargo, akwai maki na sama da iyakar baka. Don yin samfuri mai sauƙaƙe, daga mdf kauri daga 12 mm sha wani tsiri 50x1830 - Zai taimaka wajen sanya arCs a kan nau'i biyu na blanks. Ta wannan hanyar, uniform da m arcs sun makale kan manyan abubuwa da kuma wajen kera kayayyaki daban-daban, inda ya cancanta.
![Leanter daga dogon plank](/userfiles/37/4919_5.webp)
Bayan haka:
Sanya kusurwoyin da aka yanka a ƙarshen kowane ɗayan barna.
A gefen gefe na A, muna lura da tsawon b;
A ƙarshen gefen bankin D, akwai yankan semicmular.
A cikin dukkan wuraren da aka ƙayyade a cikin zane-zane muna yin rami tare da diamita na 6 mm.
Mai da hankali kan wuraren da aka sanya kuma yin kusurwa, a mai riƙe da sa, kuma bangarorin biyu, da kuma rakunan suna kuka ƙarshen. Tare da taimakon ribbon gani akan madauki mai alama, mun yanke gurasa, yin waje da baturin. Bayan haka, komai yana nika da kuma cire haɗin gefen ɓangarorin (muna amfani da farin ruhu don cire alamun Scotch).
![Grinded Bidiyo](/userfiles/37/4919_6.webp)
A baya na rakunan, sha tongs (tsagi), a kan wani sashi na kusa c - The folds.
![Cikakken zane na giciye na giciye na tarkar da Majalisarsu makircinsu](/userfiles/37/4919_7.webp)
Cikakken zane na giciye na giciye na tarkar da Majalisarsu makircinsu
Daidaita iyakar gefen bangarorin, sa guraben a kan tebur don haka gefuna masu lankwasa. Matsa a gare su baya B, lura da kusurwar ƙananan bevel a kanta. A wannan kusurwa, za mu kafa tlter da kuma tafiya da aka gani tare da yayyafa a ƙarshen ƙarshen scos na baya allon.
![Shan rack of Torchara](/userfiles/37/4919_8.webp)
Kayan katako yana da kyau a wurin aiki wanda koyaushe zaka iya amfani da abubuwan da ta yi. A cikin lamarinmu, kuna buƙatar yanke abun da aka sa 3, inda kewayon kowannensu yake 25 mm. Za su raba bangarorin A. Don yin wannan, an saka gefen su a kan tebur don aikin gona, tare da taimakon clamps, sun gyara ɓangaren rack b a kansu, bayan an canza shi daga gare su Tags, muna lura da tsawon tsayi. Bayan cire shirye-shiryen bidiyo, muna kuka da baya ga girman da ake so.
Zai zama mai ban sha'awa a gare ku: kayan kwalliya na Loft: yin hannuwankuA cikin tsagi na ɓangaren ɓangaren B, muna amfani da manne tare da ɓangarorin ɓangarorin a, a daidaita ƙananan ƙananan ƙananan, bayan haka an daidaita ƙananan glu. Me kuke buƙatar duk bayanan ƙirar, zaku iya duba cikakken zane a sama.
Lura! Don yin bene tare da hannuwanka mai santsi da kyau, a cikin rami na ɗan lokaci kana buƙatar saka huluna ko studs. Wannan zai ba da damar daidaita gefen titi. Don shigar da cikakken bayani game da baya gwargwadon, ya zama dole a aiwatar da dukkan aiki, farawa daga ƙasa da motsawa.
![Farawa da baya na bene](/userfiles/37/4919_9.webp)
A cikin mashaya na sama, mai riƙe da harshe tare da girman 10 mm.
![Zace sashen giciye na belin](/userfiles/37/4919_10.webp)
Zace sashen giciye na belin
The sag disk nuna a wani kusurwa na digiri na 13, bayan wanda muka tsunduma da wani ɓangare na saman babban tsiri na tsawon, wanda aka nuna a cikin bita cikakken zane a sama. Yanzu na nuna gangara ta hanyar diski ta digiri 16 kuma ya yayyafa wani ɗan gajeren ɓangaren saman katako, an daidaita shi a kan tsarin ɗaya. Daidaita iyakar hanyar hurarrun sassan, mun manne musu zuwa gefe na mai riƙe da D.
Mun sanya tushe
Dalilin samfurin shima ya yi itace da hannayensu. Daga abu (mm lokacin farin ciki) kuka da kuka:
babban bar f;
Cikakken back flull g.
![Cikakkun haɗin haɗi](/userfiles/37/4919_11.webp)
Cikakkun haɗin haɗi
Ta hanyar yin guraben ƙananan ɓangarorin, muna la'akari da waɗannan abubuwa masu zuwa:
A kasan braket h ana yi a kan 3 mm fadada da 6 mm sun fi girma a cikin adadi;
A kasan bayan da aka yi da 3 mm mafi fadi fiye da ƙayyadaddun masu girma dabam.
Bayan da ya koma 25 mm daga gefuna na saman baya, muna yin ramuka na oblique. Abubuwan da kanta glued kuma a gyara ta hanyar zane-zanen da ke gab da ƙarfi a gaban fari.
Don yin fitila na waje, tare da hannuwanku, cikakken aiki mai aiki na ciki, kuna buƙatar tunani game da injin lantarki zai zo wurinsa. Sabili da haka, kamar yadda aka nuna a cikin adadi a ƙasa, a kasan tsakiyar ɓangare na ƙasa na baya na baya Na, mun yanke wani wuri don kebul na lantarki. Bayan haka, a tsakiyar cikar buduwa, zamu sanya wani tsagi 3 × 19 mm.
![PAZ don kwanciya na USB na lantarki (Wayoyi)](/userfiles/37/4919_12.webp)
PAZ don kwanciya na USB na lantarki (Wayoyi)
Mayar da hankali kan zane a ƙasa, muna yin rawar lantarki ramuka, yin daga gefuna na indent na 25 mm. Yanzu, sakamakon aiki yana da haske kuma an gyara shi ta hanyar zane zuwa ƙananan Billet N.
![Gidauniyar Tharshar](/userfiles/37/4919_13.webp)
Danna don faɗaɗa
Sanya siffar saman Layer na tushen f / g, a yanka da niƙa. Wadannan billets an sanya a kan ƙananan h / ni, a daidaita cewa ƙarshen saman baya G ya juya da 10 mm dangane da ƙarshen ƙasa na baya I.
![Alamar Gidauniyar](/userfiles/37/4919_14.webp)
Don yiwa alama a cikin ƙananan layer h / i, muna bayar da saman blanks f / g (hoto sama da), yana yin izinin 10 mm. A lokaci guda, maimakon zagaye akan sasanninta, layin kai tsaye. A cikin cikakkun bayanai na ƙananan Layer, muna fama da ramuka don ƙwanƙolin m na scors huɗu. Wuraren hako shingaye tsari da zenker, bayan haka mun cire duka yadudduka na tushe.
Mai da hankali kan tsarin tushe da ke sama, muna yin ramuka:
A gaban saman f da kasan n Cikakkun bayanai na 10 mm;
A cikin ƙananan ɓangare na gaba H - 38 mm.
Bayan haka, muna shan ƙasa h / i a kan salo.
Mun yanke Jack J, barin gefen sifarwar rectangular blank (ba tare da dogon bevel ba).
Zai zama mai ban sha'awa a gare ku: teburin poker tare da hannuwanku - a wasan e e, mutane suna koya akan hanya
![Sojojin Racksera](/userfiles/37/4919_15.webp)
Gyara shi da clamps, bayan wanda muka guga shi da aka shirya a baya ɓangaren rack A / B (ƙananan ɓangarenta ya zama mara amfani da teburin don dacewa don dacewa da haɗin). Yanzu muna canja wurin ajiye abin da baya na bashin a ciki da kuma yanke aikin da ake so. Bayan haka, an goge shi, da kuma haƙoran haƙarƙarin Sandaper ko mai shiga tare da ƙananan hakora.
![Alamar gaban gaban katako](/userfiles/37/4919_16.webp)
Cikakkun bayanai J ne glued kuma an gyara ta hanyar ajiyar kansa zuwa saman Layer na f / g. Sannan mun manne kuma mu amintar da billets na ƙananan Layer H / I.
Mun yanke sandar zuwa (zai rufe kebul na wutar lantarki), muna niƙa a cikin grove, kamar yadda aka nuna a hoto.
![Haɗe kan plank](/userfiles/37/4919_17.webp)
Fresh rack zuwa tushe
Danna ragin zuwa ga sojojin. A ciki, ta bayan bangarorin da muka yi rawar da muke yi wa ramin da dunƙule sassan.
A saman gaban gindi F, akwai wurin da rack A / b, bayan an cire shi. Muna adawa da tushen F da Kuka. Sannan ramuka daga kasan bukatar a rarrabu.
![Ɗaure da torchara](/userfiles/37/4919_18.webp)
The J, mun manne da rack A / b, sannan mu fito da sukurori. A gefen ɓangarorin rack, ta hanyar ramuka da aka yi a gindi, muna rawar jiki jagorar ramuka. Gyara rack ya danganta ne akan zane-zane. Zuwa ga bangarorin a, wanda aka haɗa a cikin nade, tare da taimakon clamps muke danna gaba ɓangaren rack c, ɗaukar kusurwar bevol a ƙarshen ƙarshensa, bayan wanda muke cire clamps da cika SCO. Gudanar da kayan aiki a cikin wuri, an guga ƙananan ƙoshin sa zuwa gindin kuma canja wuri na tarinps daga gefen bangarorin, muna alamar ƙarshe. Mun banbanta a mashaya kusa da kusa da brapping zuwa gefen gefen ragon.
![Skosa Markup](/userfiles/37/4919_19.webp)
Sanya mai riƙe
Sanya siffar fararen hannu na l da wurin da za a gano ramin tsakiyar. Ta hanyar wani lakabin, mun yanke aikin, polarate shi tare da kwanciya.
![Hinada farantin](/userfiles/37/4919_20.webp)
Juya D / e, sanya shi a kan tebur don jikina kuma tsakanin ɓangarorin ɓangaren d saka sashin matsakaici, sashin giciye wanda shine 6x6 mm. Sun sanya farantin hinada a kai, a daidaita da ramin abin da aka yi a ciki tare da rami na tsakiya na gefe. Ta amfani da clamps, sanya datsa datsa zuwa gefen da ke zaune. A cikin rami na gefen da ke kusa, saka rawar soja, sannan a duk faɗin farantin da muke rawar jiki rami. Mun dauke shi, goge goge, gyara tsakanin bangarorin gefen, amfani da kayan daki na 25 mm (2 inji mai kwakwalwa.).
![Shigarwa na farantin tiyata](/userfiles/37/4919_21.webp)
An saka mai riƙe da wanda aka tattara D / E / L tsakanin ɓangarorin rack da kuma gyara sawun don kayan ado da 50 mm. A kwance sanadin ƙarshen mai riƙe, sannan gyara dogon trimming.
A kan farantin da aka yi l akan bangarorin biyu da muke danna kan clamps tare da kauri na 6 mm, da rami daya. Muna haɓaka ƙarshen mai riƙe da D / E / L ta 130 mm da faranti na baya sune na biyun. Ramin rami na karshe bayan an tashe zane ta wani 130 mm.
![Ramuka ramuka a cikin farantin](/userfiles/37/4919_22.webp)
Muna sanya kai na:
A kan trimming, kauri daga 13 mm yana sanya da'irar (a diamita ya kamata ya zama 25 mm);
A tsakiyar da'irar, muna rawar soja wani rami na 6 mm;
Billet a kusa da da'irar yana yankan ƙasa kuma yana nika sandpaper da Griny 220.
Daga sandar karfe 6 mm, mun yanke blank tare da tsawon 76 mm. Muna amfani da manne a ciki da saka a kai m (tip na sanda ya kamata ya yi 6 mm). Bayan bushewa da manne a cikin ramuka na farantin l da gefen rack ɗin kuma saka hannun rufewa.
Za ku yi sha'awar: 'yan tukwici don ɗaure shiryayye zuwa bangoAddara Abazhur
Mai shirya filayen da aka ƙira na iya zama. Ana iya siyarwa a cikin shagon ko bincika tsakanin tsoffin abubuwa. Samfurin zai yi amfani da asali idan kun nuna fantasy kuma kuyi inuwa fitila don baƙin ƙarfe tare da hannuwanku. Bugu da kari, an yi firam ɗin da sauki.
Don ƙirƙirar abubuwan da aka yi mai riƙe da - mashaya n da farantin O - daga kayan tare da kauri mai 20 mm, mun yanke billet, girman wanda shine 6x305 mm. Komawa daga biyun ƙarshen aikin da 5 mm, muna yin tsagi, kamar yadda aka nuna a zane. Mun datse daga kowane daga cikin mashaya guda n da ɗaure su ta amfani da tef ɗin gefe biyu. Maskar ramuka D5.5, kuma akan abubuwan har sai an basu haɗin ba.
![Cikakken bayani game da mai riƙe](/userfiles/37/4919_23.webp)
A cikin ragowar wani yanki na rarraba kayan da ke da nisa da rabi kuma a tsakiyar da muke rawar jiki Ramin D10, yana komawa daga ɗayan ƙarshen 16 mm. Mun yanke wani sashi tare da tsawon mm 32 (ramin dole ne ya bushe). A sakamakon hanawa farantin shine glued zuwa ɗamara n da gyara ta amfani da clamps.
Mun cire duk kayan haɗi, a hankali duk niƙa kuma amfani da haɗin kai.
Mun tattara samfurin
Mun tattara dukkan sassan samfurin sai n / o Dutsen. Mun samar da kebul na cibiyar sadarwa ta hanyar F-k da rack A-C, shafa shi a kusa da farantin hannu na d / e. Mun bar ƙarshen kusan 90 cm tsayi, wanda muke ɗauka:
riga tare da zaren ciki;
goro;
Hanawa n / o;
na ado na ado;
Wani ɓangare na bututu yana da zaren waje.
Duk gyara akan dutsen farantin o, ta amfani da busassar wurin da zaren ciki.
A cikin fitilar zuwa rami mai hawa, mun tayar da tip na waya kuma mu kara kwayoyi biyu. Tunarsa ɗayansu, gyara fitilar, na biyu bar ɗan m. A cikin babban tushe na kwararan fitila biyu, muna samar da waya, da kuma kashin baya da kanta yana gyara hannun riga tare da zaren ciki tare da zaren waje).
![Shigarwa na katako mai katako a fitilar fitila](/userfiles/37/4919_24.webp)
Danna don faɗaɗa
Haɗa ƙarshen waya a cikin kumburi na musamman kuma haɗa su tare da wayoyin katako. Ja da wuce haddi na waya baya da rufe zane tare da murfi.
A gefe na mai riƙe da d tare da taimakon screed don kayan kwalliya a kan 38 mm creakim. N / o mai riƙe. Bayan haka, wani ɓangare na waya mai shimfiɗa ta hanyar matsayin samfurin kuma saka cibiyar sadarwar.
Samfurin ba zai yi aiki ba idan ba a saka fitilar a ciki ba. A cikin lamarinmu, zaku buƙaci kwararan fitila biyu. Kaurace su a cikin samfurin kuma duba aikinta ta saka filogin cikin cibiyar sadarwa.
Bayan shawarwarin da aka bayar a sama, zai yiwu mu yi fitila tare da hannayenku a gida. Kyakkyawan samfurin zai cika ciki kuma zai ba ku damar karanta duk wasu mujallu tare da isasshen haske.
![Jerin kayan shimfidar wuri suna yin shi da kanku](/userfiles/37/4919_25.webp)
Misalai na fitilu
![Labaran da ba a saba ba da Liblshar](/userfiles/37/4919_26.webp)
![M fitila](/userfiles/37/4919_27.webp)