A few days in full immersion and comprehending knitting on the fork. For me, this is a novelty and I, by and large, I knit a crochet. But here is such an interesting knitting for a fork, it's fascinating and at the same time painstakingly and long enough. It's timely looking at the craftsmen It seems that everything is so fast and easy. But here even to buy forks is almost impossible in my familiar stores on sewing and knitting. In some stores, sellers in general, the eyes rounded without understanding what I'm talking about.
MK plug lesson 1.
I bought only 50 ml fork - 5 cm between rods.
MK plug lesson2.
The design of the fork should be the most hard. I can not say that. I can not say this fork when knitting, even with free, it is still to converge, and no longer 5 cm, and less. And this fork is short, the newcomer is convenient to knit But the motives that will then connect will be short. Many loops do not need to say here on the Palantine. And I understand that you need to immediately recruit quite a lot of loops for the entire length of the product.
Teaching is better to start quite thick yarn
Connection of elements MK plug lesson3
This is such a wide and spectacular braid up with a middle.
Already many of course first described, with the experience that came. But when it started to knit, no idea did not have any ideas.
Then he removed the loops from the fork. It was a drawing on the lesson, but it's too early.
Disabled, began to oblige loop in a different color.
It was interesting for me to know how to connect the motifs. Therefore, trying the air chains to be imposed on the edge.
But it is except for a knitted bracelet-cuffs suitable.
I got a lace ...
Further decided to take a thinner yarn of white color, I have it in sufficient quantities on the product. It said to fix the plugs at the bottom of the plank, which in ideas I understand it should be up, but it was not convenient to knit.
Now imposed more loops, tightly on the plug.
And what only the length got when he took off from the fork.
Already beautiful.
But I decided to immediately unsubage the fans. In one MK on knitting on the fork did not find the information -1-how many loops to dial on the plug for palatine. 2-ways to knit with the top strip by the latch. 3-If short motives, as they are inconspicuous, or all Taki need to immediately recruit a large number of loops on the length of the pasting. On my short forks a lot of loops do not gain, just such a length.
Here and fans already.
Of course, I was already glad.
My MK How to make an independently universal plug.
Why I decided to make a fork myself, because I could not find the plug on sale 10 ... And of course the rods of the fork should be long, probably 25-30 cm in length so that you can dial a large number of loops, the entire length of the product you want to tie. And of course, it is much easier to immediately impose a looping, and not to remove short motives.
Found a wooden rail. Wheel to cut it, sandpaper edge paper is cleaned and make them smooth. Santimeter To measure those distances that are needed for holes.
I measured 10.5 and 20 cm.
Found two spokes of 3 mm in diameter.
And of course, all emery paper must be cleared so that this is not.
Next, it is certainly possible to cope with the necessary drills and drills. But I gave my wife, he has a different diameter of the drill and experience of course. He pulled the diameter of the needles.
In the bar, the needker should be very and very tight. Therefore, it is necessary to pick up the drill. At first 2,8mm drilled, the needker did not enter, then 2.9 mm, also not included,
Then they tried to drill 3 mm.
They were afraid that the needker would slip, but she just needed, was very tight.
Already the picture is drawn. It will be with the top strip by the latch.
In general, 3 mm, the drill was needed for the spokes of 3 mm diameter. It will be a dense good entry.
This is this universal plug. It is possible to rearrange the needles for 5 cm, 10 and 20. Only the top bar for 10 is made, the most running width. But the top bar can then be cut off the new bar (this is a rake, in the construction store I bought) and make on The necessary cm holes. I am 10 cm fork for 10 cm.
Then I started to knit a lot of loops on the joy. It didn't knit without the top locking planner. I got the ends on a centimeter 2.5, and it shouldn't be. "I didn't understand that without the top plank it would not be able to knit normally. I didn't go with her It can be more convenient to knit ... I took herbs ... I wanted fluffy palatine, I saw such already. But there was a lot of "but" ...
Who knows him how many loops need to be dialing for a paletenna Let's say 1.8 m in length ... I scored almost all the sake ...
And quietly began to remove the product from the fork ....
And what kind of brook caught that in words it was not possible to transfer it. I didn't work out. Everything stretched out and stretched into a narrow strip, no loops, the yarn is complicated. I wound on the unattainable. And the work covered ... Tears rolled out of the eyes I still can still understand anything that happened ... I can't understand everything ... why the product stretched so much, the length was meters 10 .... the loops are no longer found ... you can't imagine what This is a bummer, disappointment and tears ... If I had been clear, the reason, and then it was already knitted samples, because it turned out, and here so much time, labor, and nothing happened ...
Here, of course, everything is fine, it's a little removed loops from the fork. But then the horror happened.
After such a defeat, probably, any other person spat, or everything would be broken. Thus, I decided to go with tears in my eyes. In 2 o'clock in the morning, again the white yarn again and decided to tie it on these new forks, to check everything on another yarn.
Since I was interested to know the result as soon as possible, and I scored a little loops, only 70 about it. Yes, and it was scary to dial a lot to get a lot in order not to break down again. But I took off the loop from the fork ... and everything in "Agura". The heart has become easier.
And he began to immediately unscrew the fans.
First one side.
Then the second side contused.
Hung on a pin.
It turned out more than 5 cm with forks.
Now I already knit a more subtle middle between the peels. Today I saw the MK as knitted on wooden forks, there will not lead anything in the middle, it will be stable and "Iron". He does other plugs, no longer universal, 10 cm, from the rail But the next time I will tell you and show new plugs, and how do you get knitting.
In the meantime, my experience with 5 cm and from 10.With, they hang these motifs, short of course, but you can also do something with them.
Of course you can already knit on the universal forks that I am quietly and do it. But it's still better and easier to knit without an upper fixing plank. I think that new forks will be prepared. This knitting will be added me. With samples, with errors, with bugs specific And tears in the eyes. It will be funny for experienced knitters. It will be ridiculous, but I don't care. In order to sell 10 I can not, and more too. And of course it is better to immediately have the right forks and learn to them. The same creativity has been soothing that ready As you can see, I hope for success.
And of course, if anyone knows the answers to my questions, Pliz write. I didn't find it all the subtleties. That's why there is no long on the air ... Maybe someone uses my experience, my mistakes, and my MK of the Universal Fork.
Alla shared.
A source